01 — Main Switchboards (MSBs)
Main Switchboards (MSBs)
Our main switchboards form the heart of your site's electrical network. Engineered around verified reference designs, each MSB is built for safe service access, future expansion and compliance with AS/NZS 61439.
AS/NZS 61439EngineeredService-friendly
- —High-current bus arrangements
- —Internal separation options to suit site needs
- —Withdrawable and fixed circuit breaker configurations
- —Indoor and outdoor rated options
- —Integrated metering and protection
- —Top or bottom cable entry, dual-source ready
Configuration
Fixed, plug-in or withdrawable
Segregation
Suited to site operations
Environment
Indoor or outdoor rated
02 — Distribution Boards (DBs)
Distribution Boards (DBs)
Whether wall-mounted tenant boards or large floor-standing DBs, we build to AS/NZS 61439 with clean circuit labelling, branch-circuit metering options and the drawings your site engineer actually needs at handover.
AS/NZS 61439Metering-readyTidy build
- —Engineered to AS/NZS 61439
- —Surface or recessed mounting
- —Wide range of pole counts
- —Surge protection options
- —Branch-circuit metering ready
- —RCD and RCBO protection options
Mounting
Surface or recessed
Metering
Branch-circuit ready
03 — Motor Control Centres (MCCs)
Motor Control Centres (MCCs)
Our MCCs combine engineered busbar systems with withdrawable starter modules, intelligent drive compartments and industrial communications to your DCS or SCADA — vendor-agnostic and built around what your plant already runs.
Withdrawable optionsVendor-agnosticIntelligent MPR ready
- —Withdrawable, plug-in or fixed bucket designs
- —Variable-speed and soft-starter packages
- —Industrial network integration
- —Intelligent motor protection options
- —Hot-swap options for critical drives
- —Segregation to suit site operations
Bucket types
Withdrawable, plug-in or fixed
Protection
Intelligent motor protection options
Comms
Common industrial protocols
04 — Power Factor Correction (PFC)
Power Factor Correction (PFC)
Poor power factor inflates demand tariffs and stresses upstream transformers. We size detuned PFC banks against measured harmonic profiles — never rule-of-thumb — and deliver active filters where harmonic content demands it. Our engineering team specialises in harmonic balancing and thermal management on capacitor banks.
DetunedActive filteringHarmonic engineered
- —Detuned reactor designs matched to the load
- —Active filtering for harmonic-heavy sites
- —Automatic correction to targeted power factor
- —Thermal-imaged commissioning report
- —Tariff payback modelling included
- —Capacitors sized for realistic ambient conditions
Configuration
Detuned or active
Target PF
Set to your tariff and load
Sizing
Based on measured harmonic profile
Control
Multi-stage with harmonic alarming
05 — Solar, BESS & EV Panels
Solar, BESS & EV Panels
From rooftop C&I to utility-scale battery and EV charging infrastructure, we engineer AC and DC switchgear that integrates cleanly with major inverter and BESS platforms and the local network grid-connect requirements.
Grid-connectBESS & EVVendor-agnostic
- —Grid-connect compliance to AS/NZS 4777
- —DC isolation and combiner panels
- —Inverter-matched output assemblies
- —Battery isolation and pre-charge
- —Network-ready protection schemes
- —EV DC and AC charging infrastructure
Scope
Rooftop through to utility scale
Integration
Vendor-agnostic inverter and BESS
06 — Meter Panels & Service Pillars
Meter Panels & Service Pillars
Multi-tenant, embedded-network and EV-charging meter panels engineered to each state's Service & Installation Rules and the relevant network requirements. Hot-dip galvanised pillar options for street-side installations.
SIR-alignedEmbedded networkEV-ready
- —State-by-state SIR alignment
- —Embedded network ready
- —EV-charging metering modules
- —Hot-dip galvanised pillar options
- —Network-authority ready drawings
- —Utility-grade metering options
Metering
Utility-grade options
Mounting
Pillar, pad-mount or surface
Coatings
Hot-dip galvanised + 2-pack epoxy
07 — Control & Instrumentation Panels
Control & Instrumentation Panels
Compact field stations through to fully-engineered marshalling cabinets. We work to your wiring standards or deliver against ours — CAD-driven, factory-tested and built for the platforms your team already supports.
CAD-drivenIntrinsically safe optionsOEM-ready
- —Vendor-agnostic PLC platforms
- —CAD-driven wiring diagrams
- —Intrinsically safe and hazardous-area options
- —On-site FAT facility
- —OEM volume-build programs
- —Network switches, fibre and copper structured cabling
PLC platforms
Vendor-agnostic
Documentation
CAD schematics and 3D
IS / hazardous area
Available on request
